Stump and Pasture Clearing near Eagle River, Vilas County, Wisconsin

Stump and Pasture Clearing near Eagle River, Vilas County, Wisconsin

Near Eagle River in Vilas County, Wisconsin, pasture brush and fence line growth come off with a skid steer brush cutter. Stumps left after tree work need a stump grinder. Match each attachment to your machine hydraulic flow before you order. On many low-flow and standard-flow machines, start with an HD Closed Front Brush Cutter (starting at $7,744) for brush and fence lines, then add a Reflex Stump Grinder (starting at $10,200) for leftover stumps.

Finance from $199/mo, and call Skid Steer Nation for a fit check before you buy.

Your opening did not fill with brush overnight. Saplings pushed in from the tree line while sweet fern and bracken filled the dry sand ridges. Old pine and aspen stumps still sit where a cut was made years ago.

Cattle walk around them, a rotary mower skips them, and new seed fails next to the crown.

Vilas County ground makes the job different from southern Wisconsin farms. On many ridges and outwash flats, Rubicon sand is a major map unit. It is excessively drained sand with high or very high saturated hydraulic conductivity. Water moves through it fast.

On nearby outwash with a thin loamy top, Pence sandy loam is somewhat excessively drained. Permeability is rapid or very rapid in the sandy outwash below. Large peat map units also sit in the county. Those wet organic flats are a poor place for routine pasture clearing traffic.

This guide shows how to clear stump and pasture brush on that mix of sandy northwoods soils with skid steer attachments you can own. Specs and prices come from live product pages, not estimates. Prices were checked on skidsteernation.com on November 5, 2026.

What fails first when you skip the soil check?

University of Wisconsin Extension says every pasture renovation starts with soil. Soil type and texture do not change, but nutrient status does, so sample to a 6 inch depth every 3 to 4 years.

If you seed into a sand ridge without fixing fertility or seed to soil contact, the new stand fails and brush returns faster than grass.

In Vilas County (NRCS survey area WI125), Rubicon sand, 0 to 6 percent slopes covers about 49,028 acres. That is the largest mineral map unit after open water and peat. Rubicon sand, 6 to 15 percent slopes adds about 19,842 acres. Pence sandy loam, 0 to 6 percent slopes covers about 22,340 acres, with more Pence on steeper slopes.

Official series descriptions rate Rubicon as excessively drained sand formed in sandy deposits. They rate Pence as somewhat excessively drained, formed in a thin loamy mantle over stratified sandy outwash. The Pence frost free period ranges from about 70 to 135 days. The Vilas series, which occurs with these sandy landscapes, lists a frost free period of about 90 to 120 days.

What that means on the machine:

  • Plan brush and stump work on Rubicon and Pence ground when the surface is firm and dry, or when the ground is frozen, so tracks do not chew the sand into soft ruts.
  • Stay off peat flats mapped as Loxley, Greenwood, and Dawson peats. NRCS rates Loxley as very poorly drained organic soil, with wet conditions at or near the surface for much of the year, so it is poorly suited to routine clearing traffic.
  • Do not treat every acre the same. Walk the wet pockets and the steep Sayner-Rubicon slopes before you start.

What tools clear pasture brush versus stumps?

Stumps and cut brush in a woodland clearing.
Stock scene of stumps and brush in a woodland clearing. Photo: Denys Mikhalevych / Pexels.

A brush cutter handles tall grass, briars, and saplings within its cut rating, but it is not a stump grinder. A stump grinder takes the stump below finished grade after the tree is gone.

Mixing those jobs burns blades, slows the day, and leaves hazards for livestock.

UW Extension notes that after woodland thinning for silvopasture, stumps and remaining trees often block a seed drill. Forage seeding needs another plan once the wood is down. That is one more reason to finish stumps before you spend money on seed.

Here is a real-spec table from live Skid Steer Nation product pages dated November 5, 2026. Use starting at prices. Configurations and options change the final number at checkout.

Attachment Starting at price Key specs from the product page Best fit
HD Closed Front Brush Cutter $7,744 Low flow 10 to 15 GPM or standard flow 16 to 26 GPM; widths 66, 72, and 78 inches; 1/4 inch GR50 steel deck; chain guards front and back Pasture brush, fence lines, and work near cabins, roads, or livestock
Open Front Brush Cutter $12,029 Standard flow 16 to 25 GPM; high flow 26 to 40 GPM; widths 72, 78, and 84 inches; cuts trees and brush up to 6 inches diameter; direct drive Heavy brush where debris throw is less of a concern
Skid Steer Brush Cutter Attachment $13,080 Widths 72 and 84 inches; high torque Danfoss motor; 4000 PSI cross port relief valve; cuts small trees up to 10 inches diameter Dense brush and larger saplings on bigger machines
Reflex Stump Grinder $10,200 24 inch wheel in 16 to 20, 21 to 24, and 25 to 28 GPM; 26 inch wheel in 29 to 33, 34 to 39, and 40 to 45 GPM; carbide teeth both sides; 1 inch thick wheel Most stump jobs on standard-flow or high-flow machines
Miller Stump Grinder $20,110 26 inch wheel; 29 to 45 GPM; weight 1,640 pounds; 30 teeth; 6-way swing, lift, and telescope High-flow production stump work

Finance from $199/mo on attachments. Flat rate freight ships nationwide. Confirm your machine GPM in the operator manual before you order.

HD Closed Front Brush Cutter skid steer attachment clearing brush.
HD Closed Front Brush Cutter on a skid steer.

Which setup should most Eagle River area owners buy first?

One clear recommendation: For most Vilas County pasture and stump cleanup near Eagle River on a low-flow or standard-flow skid steer, buy the HD Closed Front Brush Cutter first (starting at $7,744). Add the Reflex Stump Grinder next (starting at $10,200) when stumps remain after tree removal.

Why that order matters:

  • Brush and fence line growth is the daily problem on most pastures and openings.
  • The closed front keeps thrown rocks and wood under the deck when you work near cabins, roads, or livestock.
  • The Reflex covers a wide flow range. The 24 inch wheel starts at 16 GPM, so more machines can run it than high-flow only grinders.
  • Save the Miller (starting at $20,110) for high-flow fleets that grind stumps all day.

If your machine is already high flow and stump work is the main job, step up to the Miller. If you only cut light grass, a brush cutter alone may be enough. Stumps still need a grinder when they remain in the field.

Operator field tips: Work Rubicon and Pence sand when dry or frozen. Stay off Loxley, Greenwood, and Dawson peat flats. Match cutter and grinder GPM to your machine before you order.

What happens if you skip a step?

  • Skip waiting for dry or frozen ground on sand: Soft Rubicon tracks blow out, leave loose sand, and make the next pass harder on tires and forage.
  • Skip staying off peat: Organic flats mapped as Loxley, Greenwood, and Dawson peats are very poorly drained and stay wet near the surface. Keep routine clearing on Rubicon and Pence mineral soils instead.
  • Skip matching hydraulic flow: A cutter or grinder on too little GPM runs soft. Teeth and blades wear faster. The same acre takes much longer.
  • Skip grinding below grade: The stump stays as a trip hazard for cattle and a hard spot for the next mower. Seed and fill fail around the crown, which matters even more when Extension says stumps already block drilling after a woodland thin.
  • Skip soil testing before reseeding: UW Extension is plain on this point. Pasture renovation fails when major soil nutrient problems are ignored. Clearing brush without a fertility plan just opens bare sand for the next weed flush.
  • Skip timing on woodland thinning: Extension guidance for silvopasture thinning says run heavy equipment when the ground is frozen or dry, because wet traffic compacts and disturbs soil. On oak sites, spring and summer cutting can also spread oak wilt, so ask a forester before you cut.

How do you run a clean clearing day near Eagle River?

  • Walk the field and mark peat pockets against Rubicon sand ridges and Pence outwash.
  • Confirm machine flow in GPM and rated operating capacity.
  • Cut brush with the closed front cutter on firm or frozen ground and stay off soft organic flats.
  • Pull or fell trees that must go, then grind stumps below grade with the Reflex or Miller.
  • Push chips and fill so you leave a surface you can seed or graze.
  • Sample soil, fix nutrients, and reseed only when Extension timing for your method fits, whether that is frost seed, no-till, or a prepared seedbed.

Tell us what your pasture looks like

Reflex stump grinder attachment mounted on a skid steer.
Reflex Stump Grinder on a skid steer.
Sandy open ground with grass and pine trees.
Stock scene of sandy open ground and pine trees. Photo: Denzel V / Pexels.

Send a few photos of the brush, the stumps, and your skid steer model around Eagle River or elsewhere in Vilas County. We will confirm flow fit and point you to the right attachment.

You can also call for a straight estimate. No hard sell, just a clear plan and a realistic timeline.

Get a Fit Check
Call Us at (309) 471-9100
sales@skidsteernation.com
Finance from $199/mo

Diagram comparing sandy uplands with peat and muck lowlands.

FAQ

Do I need a forestry mulcher for Vilas County pasture brush?

Usually no. A brush cutter handles grass, briars, and saplings within its cut rating, while a stump grinder handles stumps. A mulcher is for heavier standing timber work, not typical pasture cleanup.

Can I clear peat flats in early spring?

Usually that is a bad idea. Large Loxley, Greenwood, and Dawson peat map units in Vilas County stay wet. Wait for firm ground, or keep clearing work on Rubicon and Pence mineral soils instead.

What flow does the Reflex Stump Grinder need?

The 24 inch wheel comes in 16 to 20 GPM, 21 to 24 GPM, and 25 to 28 GPM configurations. The 26 inch wheel is available in 29 to 33 GPM, 34 to 39 GPM, and 40 to 45 GPM. Match the option to your machine rating.

What flow does the HD Closed Front Brush Cutter need?

Low flow versions run about 10 to 15 GPM, and standard flow versions run about 16 to 26 GPM, so order the match for your machine.

How deep should I grind a stump before seeding?

Skid Steer Nation notes most skid steer stump grinders reach about 6 to 12 inches below grade by model and stump size. For many seed or fill jobs, about 6 inches below grade is enough. Check the stump grinder collection for your finish grade.

Is financing available?

Yes. Finance from $199/mo through the financing page on skidsteernation.com. Terms depend on approval.

Ready to clear your Eagle River acreage?

Get a Fit Check
Call (309) 471-9100
Email sales@skidsteernation.com
Finance from $199/mo

 

Previous Article